⚠️ Requires a Kess3 Slave Alientech device that has already been activated.
This product is a software extension, not a device.
KESS3 Slave - Bench-Boot Protocols - Boat/Jet-ski
€390,00HT
Activation of Bench and Boot protocols for KESS3 Slave covering boats and jet-skis.
Bench mode reads and writes the control unit by connecting directly to its connector. Boot mode reads and writes by connecting to specific points on the circuit board. This activation covers Bench and Boot access on this vehicle range, from older to the latest powertrains.
In Slave version, read files are encrypted. The modified calibration map is provided by your reference Master.
Control unit removal is sometimes the only viable access route on a marine powertrain, as the installation is often difficult to reach.
Specifications
- Alientech reference: KESS3SA008
- Version: KESS3 Slave
- Communication modes: Bench and Boot
- Segment: boats and jet-skis
- 12-month subscription included on a new device
A Bench power supply and the adapters for the control units being programmed are required.
Complete with another protocol
Pairs well with
Remote activation within 24/48 hours
Interest-free installment payments
Technical support in French
KESS3 Slave - Bench-Boot Protocols - Boat/Jet-ski
€390,00HT
If you have any questions, you are always welcome to contact us. We'll get back to you as soon as possible, within 24 hours on weekdays.
-
Informations d'expédition
Use this text to answer questions in as much detail as possible for your customers.
-
Customer Support
Use this text to answer questions in as much detail as possible for your customers.
-
FAQs
Use this text to answer questions in as much detail as possible for your customers.
-
Contact Us
Use this text to answer questions in as much detail as possible for your customers.
WHAT THIS PROTOCOL COVERS
Supported vehicles and modes
Please check that the category and mode correspond to your usage before ordering, as the protocol cannot be modified after activation.
Boats/Jet Skis
Outboard and inboard motors, jet skis, and recreational boats.
Bench-Boot Mode
Reading and writing directly to the ECU (Bench mode) or to its opened electronic board (Boot mode), necessary for the most secure ECUs or for cloning.
OBD, Bench-Boot or full package: how to choose?
This product only covers Bench-Boot mode. Compare with OBD-only mode or the complete pack below before ordering.
OBD only
OBD read mode
Covers only OBD mode for Boats/Jet-skis. Sufficient if you almost always work from the diagnostic socket, without removing the ECU.
Bench-Boot only
Calculators deposited: this product
Necessary for cloning or for the most secure calculators that require Bench or Boot intervention.
Complete pack
OBD + Bench-Boot
Combines both modes for Boats/Jet-skis at €690.00 excluding tax, cheaper than buying them separately (€980.00 excluding tax).
Activation Requirements
How is the protocol activated?
Activation is performed remotely on your KESS3 Slave device, via your Alientech ID, within 24 to 48 hours after your order.
Is the protocol time-limited?
No, activation is permanent for the Car/LVC category and OBD-Bench-Boot mode. Only vehicle compatibility updates are covered for 12 months, then renewable.
Can I add more categories later?
Yes, each category and mode can be ordered separately or as part of a pack. You can complete your KESS3 Slave as your business grows (Motorcycle/Quad/UTV, Agriculture/Heavy Duty/Bus, Boats/Jet-ski).
FAQ
Does this protocol work without a KESS3 Slave unit?
No, this is a software extension: it requires a KESS3 Slave Alientech device that you already own and that has been activated.
Can I add OBD mode later on Boats/Jet skis?
Yes, by ordering "OBD Protocols - Boats/Jet-skis" (590.00 € excl. VAT) separately. You can also check if the complete Boats/Jet-skis OBD-Bench-Boot pack (690.00 € excl. VAT) is more advantageous for your needs.
What is "full protocol activation"?
This is the equivalent of this protocol, but extended to all vehicle categories (Cars/LCVs, Motorcycles/Quads/UTVs, Agriculture/Heavy Goods Vehicles/Buses, Boats/Jet-skis) for the chosen mode.
Is the protocol different between a KESS3 Slave and a KESS3 Master?
The content of the protocol (vehicles and modes covered) is identical; only the product reference changes depending on your device's version.
Become an RS-Tronic reseller
- €0 Entry Fee: No entrance fee to join the group
- 90+ Resellers in France and Internationally: A network that proves the model works
- Bench-Developed Files: Manufacturer tolerances and anti-pollution standards respected
- Preserved Autonomy: The strength of a large group, your company remains your own